Hansa · Part no. HAN-3421
Gunwale guard, Hansa 2.3W and 2.3S
Hansa · Part no. HAN-2412 · Proasail.com, official Hansa distributor
- Made to order · about 3 months
- Free pickup in La Roca del Vallès · Mon-Fri 9:00-16:00
- Secure card payment · Visa, Mastercard, Maestro
- Returns within 14 days · Shipping and returns
Not sure it fits your boat? Write to us: the reference HAN-2412 is already in the message.
Description
This part works right where the boat meets the shore. When you approach the pontoon or the hull rests against it while mooring, the strip takes the rubbing instead of the gelcoat. With the boat in the water, it keeps protecting the edge during every manoeuvre.
The material makes the difference. The manufacturer switched to a stiffer compound, which stretches little and resists pulls that try to peel it off. In exchange, it is less pliable when fitting, so it is best heated to adapt to the edge without effort.
It is fixed with fast-curing polyurethane adhesive and with blind aluminum rivets at the ends. Other urethane rubber adhesives also work, such as 3M 5200 Fast Cure or Sikaflex. The adhesive is sold separately.
To make it last, prepare the surfaces well. The plastic releases an oil that weakens the bond over time. Clean it with acetone and sand the gloss off the gelcoat where it will be bonded. If the boat already had a previous piece, first remove any old residue.
Fitting and use
Preparation: clean the strip with acetone and sand the gelcoat gloss in the bonding area. If the boat is old, first remove any remains of the previous adhesive. Fit test: dry-fit the strip and drill through both the strip and the gunwale edge at each end, using a 3/16" bit. The holes should sit about 75 mm on either side of the centreline. Do not rivet yet. Heating: coil the strip and heat it for about 30 minutes, to around 60 °C, so it becomes flexible. Ends: fix both ends with blind aluminium rivets, without twisting the strip. Bonding: working from the stern and the bow, lift the strip and apply a bead of urethane adhesive about the thickness of a pencil along the centre. Work in 1 m sections and press down with your palm. Cleaning: remove excess adhesive with acetone or white spirit and small rags. Hold the strip in place with masking tape until the adhesive cures. Then go over the edge with a blunt blade, without cutting the PVC.
Compatibility
Listed in the Hansa 2.3 parts diagram.
Which boats it fits
Not sure it fits your boat? Write to us.
Specifications
| What's included | One length of gunwale guard strip for the Hansa 2.3. Adhesive is sold separately. |
|---|---|
| Sold as | Sold per unit (one length of strip). |
| Strip length | 5670 mm |
| Material | flexible PVC |
| PVC grade | harder and less flexible since April 2018 |
| Recommended adhesive | Fix 190 white, 290 ml fast-cure cartridge |
| Alternative adhesives | 3M 5200 Fast Cure and Sikaflex |
| End fixing | blind aluminium rivets |
| Fitting temperature | around 60 °C |
Frequently asked questions
What adhesive do I need to bond it?
We recommend Fix 190 white, in a 290 ml fast-cure cartridge. Other urethane rubber adhesives, such as 3M 5200 Fast Cure or Sikaflex, also work. The adhesive is sold separately.
Do I need to heat the strip before fitting it?
Yes. Since 2018 the PVC has been a harder grade and less flexible. We recommend heating it for about 30 minutes, to around 60 °C, so it becomes malleable.
Can it be used on a boat that already had a gunwale guard?
Yes, but any remains of the old adhesive must be removed first. A coarse-grit sanding disc removes it. Then clean with acetone.
Downloads
Recommended products
More parts for this boat and similar parts
-
On order€273.46 €226.00
-
-
-
Hansa · Part no. HAN-6131.71
Hansa 2.3 fixed servo system: 70 rpm main, no battery
On order€2,128.39 €1,759.00 -
-
-
-
Hansa · Part no. HAN-4726.2
Cockpit skirt hooks (8 pcs), Hansa 2.3, 303 and Liberty
On order€53.24 €44.00 -
Hansa · Part no. HAN-6503
80 rpm mainsheet winch without clutch, Hansa 2.3S, 303S and Liberty S
On order€1,167.65 €965.00 -
Hansa · Part no. HAN-6133.81
Hansa 2.3 servo system: 80 rpm main, no battery
On order€2,711.61 €2,241.00









