Self-Tacking jib complete kit for Wētā #1000+
Part no. 30304
- On order: get it around Thursday 3 if you order today
- Free pickup in La Roca del Vallès · Mon-Fri 9:00-16:00
- Secure card payment · Visa, Mastercard, Maestro
- Returns within 14 days · Shipping and returns
Proasail.com is the official Weta distributor.
Not sure it fits your boat? Write to us: the reference 30304 is already in the message.
Description
Complete Weta self-tacking jib kit for Wētā#1000+ (Self Tacking Jib Complete Kit for Wētā#1000+ (White)), part no. 30304. It is for Wētā#1000+ and the colour is white (White).
The 2022 self-tacking jib kit consists of a deck-mounted track and a new, slightly smaller jib. It lets you tack and gybe hands-free, especially combined with the Weta Twin Tiller kit. Kit contents (Self Tacker Kit Contents):
- Track and supports (Track and Supports).
- Track car (Track Car).
- 1 shackle (1x Shackle).
- 1 saddle, a lacing eye (1x Saddle).
- 2 Ronstan Series 20 ball-bearing blocks RF25109 (2 X Ronstan Series 20 Ball Bearing Block RF25109).
- 3 m of 4 mm Dyneema (3m x4mm Dyneema).
- 1 m of 3 mm Dyneema (1m x3mm Dyneema).
- 2 m of 3 mm Dyneema-core rope, red (2m x 3mm Dyneema core (red)).
New boats have the self-tacking jib track supports moulded into the deck. The standard jib can still be used on those new boats. For the newer boats with the track moulded into the deck, you only need to fit the rigging pack that comes with the kit. In step 1.2 of the fitting (For Weta #1000+), place the straight-edged self-tacker moulding hard up against the mast step, without overlapping it. The curved moulding must face towards the bow. The installation requirements (Installation Requirements) include MSR structural adhesive. Use only flexible marine-grade structural adhesives: Sikaflex 292i, Fixtech Fix 190, 3M 5200 or Bostick Simpson MSR.
Weta spare part, Sails section.
Fitting and use
New boats have the track supports in the deck mould: you only fit the rigging pack. The straight-edged moulding is bonded to the mast foot without overlapping it, with the curve facing forward. Bond with a flexible marine structural adhesive.
Compatibility
Listed in the Weta parts diagram.
On those boats you can also keep using the standard jib.
Which boats it fits
Not sure it fits your boat? Write to us.
Specifications
| What's included | Track with its supports, track car, 1 shackle, 1 saddle, 2 Ronstan Series 20 RF25109 ball-bearing blocks, 3 m of 4 mm Dyneema, 1 m of 3 mm Dyneema and 2 m of red line with a 3 mm Dyneema core. |
|---|---|
| Sold as | Sold as a kit. |
| Technical data | Part number 30304, made by Weta Marine. |
| Colour | white (White). |
| Accepted adhesives | 3M 5200, Sikaflex 292i, Bostick Simpson MSR or Fixtech Fix 190. |
| Section | Sails. |
Product safety
- Manufacturer
- Wētā Marine · Campbells Bay, North Shore, Auckland, New Zealand · info@wetamarine.com
- EU responsible person
- PROASAIL, S.L. · Av. València, 82, 08430 La Roca del Vallès (Barcelona), Spain · info@proasail.com
Frequently asked questions
Is this the kit for my boat?
Check your hull number, which is also your sail number. This part is for hulls 1000 or higher; for hulls 1 to 999 the kit is 30305, with a recessed-type track support.
What do I clean the deck with before bonding it?
With denatured alcohol, after a light sanding with 100-grit paper. Do not use acetone or paint cleaners: they reduce adhesion.
How do I lash the turning block?
Pass the 3 mm line through the bow holes, next to the forestay bridle, tie it securely underneath so it cannot slip through, and lash the block through the middle: otherwise it can pull apart under load.
Does it include the twin tiller kit?
No. The twin tiller is a separate part, 40281, and it does not include the self-tacking jib either. Combined, they let you tack almost hands-free.
Downloads
Recommended products
More parts for this boat and similar parts









